The term archer's paradox was coined by Robert P. Elmer in the 1930s. The paradox refers to the phenomenon that in order to strike the center of the target, the arrow must be pointed slightly to the side of the target. Modern use of the term has caused the interpretation of it to be corrupted and the bending of the arrow is often considered incorrectly to be archer's paradox.
The stiffness of the shaft is known as its spine, referring to how little the shaft bends when compressed. Hence, an arrow which bends less is said to have more spine. In order to strike consistently, a group of arrows must be similarly spined. "Center-shot" bows, in which the arrow passes through the central vertical axis of the bow riser, may obtain consistent results from arrows with a wide range of spines. However, most traditional bows are not center-shot and the arrow has to deflect around the handle in the archer's paradox; such bows tend to give most consistent results with a narrower range of arrow spine that allows the arrow to deflect correctly around the bow. Higher draw-weight bows will generally require stiffer arrows, with more spine (less flexibility) to give the correct amount of flex when shot.
In order to be accurate, an arrow must have the correct stiffness, or "spine", to flex out of the way of the bow and return back to the correct path as it leaves the bow. Incorrect spine results in unpredictable contact between the arrow and the bow, therefore unpredictable forces on the arrow as it leaves the bow, and therefore reduced accuracy. Additionally, if an archer shoots several arrows with different spine, even if they clear the bow they will be deflected on launch by different amounts and so will strike in different places. Competition archers therefore strive not only for arrows that have a spine within a suitable range for their bow, but also for highly consistent spine within sets of arrows.
Less powerful bows require arrows with less spine. Less powerful bows have less effect in deforming the arrow as it is accelerated from the bow and the arrow must be "easier" to flex around the riser of the bow before settling to its path. Conversely, powerful bows need stiffer arrows with more spine, as the bow will have a much greater bending effect on the arrow as it is accelerated.
An arrow with too much spine for the bow will not flex and as the string comes closer to the bow stave, the arrow will be forced off to the side. Too little spine, or flexion, will result in the arrow deforming too much and being propelled off to the other side of the target. In extreme cases, the arrow may break before it can accelerate, which can be a safety hazard.
Watch this video to see how your arrow flexes in slow motion...
The measurement of "spine" has been standardized by the American Archery Trade Association, formerly the Archery Manufacturer's Organization, and spine measurements may sometimes be specified as "AMO spine". The spine of an arrow shaft is a measure of its stiffness. The AMO standard for measuring spine is to measure the deflection of the shaft at the midpoint of a 26-inch (660 mm) span when placed under a load of 2 pounds-force (8.9 N). The more deflection, the less stiff the shaft, and the lower its spine measurement
- ^ "Archers Paradox Explained". Texasarchery.org. 2001-06-24. http://www.texasarchery.org/Documents/ArchersParadox/Archersparadox.htm. Retrieved 2010-02-17.
- ^ "Jim Hill's Spine Tester". Jamesmhill.com. http://www.jamesmhill.com/Spine_Tester.html. Retrieved 2010-02-17.
- ^ Cosgrove, Gabriela (1994). "Wooden Arrows". The Traditional Bowyer's Bible. Volume Three. Guilford: The Lyons Press. p. 228. ISBN 158574087X.
- Ashby on Single Bevel design and effectiveness
- Pictures and discussions on the effects of Single Bevel broadheads on game
- Broadhead Sharpness and it relationship to Clotting and Bloodtrails
- Aligning the Tuffhead
- Honing the Tuffhead Single Bevel
- Archers Paradox
- The Story behind the TuffHead™
- TuffHead™ Tech
- TuffHead™ Specs
- Order Now